10,000 LB Capacity 2-Post Lift Car Auto Truck Hoist 220V Floor Plate Auto Ramp. Electric 220V/1PH/ motor with hydraulic power system. The lift offers exceptional direct-drive lifting performance. This industrial-strength car lift guarantees cutting-edge technology. Top of the line materials, a design that's ahead of its time and a 10,000-lb.
Every lift offers an abundant roster of options and accessories that allow you to fully tailor the lift to your unique circumstance. Symmetric arms design with double lock system. The highly sophisticated yet simple and dependable Series design requires very little service. Or maintenance for an overall lower cost of ownership.
Our tube arms have been reconfigured to make it easier to open doors when vehicle lift points are engaged. This is especially useful if your vehicle has low-hanging doors.
To prevent damage to your property with our two-post lift design. Low-profile, dropped-end frame contact pads. From race cars to lowered compact vehicles, this car lift has the versatility. To get under your chassis without damaging your vehicle's body or frame. Lifts come with free set of Truck adapters.
Highly duty oil slider with 10mm steel rope ensures carriage smooth moving up and down. With 8 folded profile column, provide extremely high strengthen working ability.
Driving Mode: Dual hydraulic cylinders, chain drive. Lock Release :Dual sides manual release.
Thickness of steel for pillar: 5mm. Thickness of steel for arm: 6mm.Thickness of steel for carriage :6mm. Thickness of steel for basement cover: 3mm. Steel rope diameter: 9.3mm. Steel rope pully diameter: 118mm. Double Points Safety Lock Release. Relief valve built in power pump to prevent overloading. Up-limit switch to protect cylinders working stroke used in safe length scope. Heavy duty :9.3mmdiameter cable and 118mm pulley reduce high stress on synchronization process and increase cable life. Stiffened base plate 3mm thickness.
Ultra high molecular self lubricating nylon slider ensures carriage smooth moving up and down. Lifting operation by pressing "UP" button on motor. Manual lowering operation by pressing lever. 1 sets truck adapters included.
Lifting Capacity: 10,000 lbs. Min pad height: 3-3/4(95mm). Lift height max: 70-1/16(1780mm). Drive-thru width clearance: 109-1/4 (2775mm).Time to full rise: 20-60 sec. Before installing your auto lift, check the following.
Lift Location: Always use architect's plans when available. Check layout dimension against floor plan requirements. Making sure adequate space is available. Your lift requires a 220v/ 110V, 30amp, single phase, grounded electrical source. There should be room enough to operate the lift in a safe manner and without restrictions.
Overhead Area: The area where the lift will be located should be free of overhead obstructions. Such as heaters, building supports, electrical lines, doors, lights, etc. Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.A level floor is suggested for proper installation and level lifting. Small differences in floor slopes may be compensated. If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab. New concrete must be adequately cured for at least 30 days. DO NOT install auto lift on any asphalt surface or any surface other than concrete. DO NOT install auto lift on expansion seams or on cracked or defective concrete. DO NOT install auto lift on a second/elevated floor without first consulting building architect. DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.
All models MUST be installed on 3,000 PSI reinforced concrete only. Additional concrete requirements will vary by lift.
The item "10,000 LB Capacity 2-Post Lift Car Auto Truck Hoist 220V Floor Plate Auto Ramp" is in sale since Thursday, July 9, 2020. This item is in the category "eBay Motors\Automotive Tools & Supplies\Shop Equipment & Supplies\Auto Lifts & Frame Machines". The seller is "kunding01" and is located in CA.
This item can be shipped to United States.